BookTitleOkabe Product Catalog

Summary

Okabe Product Catalog

A　B　C　G　TemporaryConstructionConcreteRebar Work Formwork CivilEngineeringBottom Pipe Supporting HookJ-shaped pipe supporting hook for bottom beamBeam depth(mm)Beam bottom spanlength (mm)Beam width (mm)200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 10002000 600 400 400 300 300 200 2001900 600 500 400 300 300 200 200 200 Separator spacing (mm) 1800 600 500 400 300 300 200 200 200 2001700 Maximum length: 600 500 400 400 300 300 200 200 200 Vertical spacing: 6001600 within 1,200 (mm) 600 500 400 400 300 300 200 200 200 Horizontal spacing: 4501500 600 600 500 400 300 300 300 200 200 200 Vertical spacing: 6001400 600 600 500 400 400 300 300 200 200 200 200 Horizontal spacing: 6001300 600 600 600 500 400 400 300 300 200 200 2001200 600 600 600 500 400 400 300 300 200 200 200 2001100 600 600 600 600 500 400 400 300 300 200 200 200 2001000 600 600 600 600 500 500 400 400 300 300 200 200 200900 600 600 600 600 600 500 500 400 300 300 300 200 200 200800 Maximum length: 600 600 600 600 600 600 500 400 400 300 300 300 200 200700 within 1,800 (mm) 600 600 600 600 600 600 600 500 400 400 300 300 300 200 200600 600 600 600 600 600 600 600 600 500 400 400 300 300 300 200 200500 600 600 600 600 600 600 600 600 600 500 500 500 400 300 200 200 200● Up to 1,800mm, when the beam depth is within 1,000mm.● Up to 1,200mm, when the beam depth is within 2,000mm.*1*2Applicable beam bottom span lengthAllowable load: 2.94kN (300kgf)Horizontal spacingfor SeparatorsHardwareinstallation spacingBeam bottom span lengthBottom beamreceiving round pipeVertical spacing forSeparatorsBottom PipeSupportingHookEasy and secureinstallation!!◆Bottom Pipe Supporting Hook and Separator installation spacing chart● The following chart shows spacing for this product, as well as vertical and horizontal spacing for Separators for the beam formwork,when the beam depth is 500~2,000mm and the beam width is 200~1,000mm.* The allowable load is applicable when Okabeform ties, separators and plastic cones areused.● Use the product within the allowable load of2.94kN (300kgf).● When using the product repeatedly, check theproduct for deformation and damage beforeinstallation.● Use film faced plywood (t= 12mm or more).● Use φ 48.6 steel pipes (t= 2.3mm or more).● After installing this product, do not place afoot or object on the horizontal pipe.Cautions● Firmly support the bottom beam formworkand both sides of beam formwork whereunequal settlement does not occur. Take ameasures to prevent the formwork deformationand collapse.● This product is intended to support the bottombeam formwork by hanging it from thebeam formwork. If the beam formwork is notrigid enough, support it at appropriate intervals.● When using this product outside the applicablescope, be sure to support the bottom beamformwork and beam formwork with supportingmaterials (Falsework, shoring prop, etc).● Example 1: When the beam depth is 1,200mmand the beam width is 750mm (*1 in chart):　 The spacing of the product is 200mm.According to ■ colored area, the verticalspacing of the Separators is 600mm, andthe horizontal spacing of the Separators is450mm. The maximum beam bottom spanlength is 1,200mm.● Example 2: When the beam depth is 1, 000mmand the beam width is 400mm (*2 in chart):　 The spacing of the product is 500mm. Accordingto □colored area, the vertical spacingof Separators is 600mm, and the horizontalspacing of the Separators is 600mm.The maximum beam bottom span length is1,800mm.◆Examples of how to read the chartSingle coverPipe receivingpartMain body:IVY bolt W1/2550Product No. B10-057051